Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
Everybody has their own individual concepts in relation to Installing A Bathtub.
Setting up a bath tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough job. If the old tub is easily available, the project can move immediately; if you need to open a wall surface to get rid of the old tub and also position the new bathtub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to move out the old bathtub and also set in the new one. See to it you have actually qualified yourself for the job as well as fit attempting it. Instead of employing a specialist to take over a halfway-completed project, it is far better to consider employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will aid you install a brand-new bathtub in your bathroom if you have actually already gotten a brand-new bathtub as well as do not require to change the plan of your previous water pipelines.
Your devices and material checklist need to comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing faucets can be fairly troublesome due to the limited access that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in location in between the faucet and the sink. Protect the tap in place with the supplier given backnut. Once the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type should be connected to the faucet ends first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bathtub
Using both wood boards under its feet, place the bathtub in the needed setting. The wood boards are useful in equally spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the tub till the spirit level checks out level.
To set up faucets, fit the bottom of the outermost flexible tap connector to the suitable supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water supply and also check all joints and also brand-new pipework for leaks and also tighten them if required. Load the bath tub as well as likewise check the overflow electrical outlet and also the regular outlet for leakages.
Lastly, fix the bath paneling as explained in the producer's instruction manual. Tiling as well as sealing around the tub should wait up until the bathtub has actually been used at the very least when as this will resolve it into its final placement.
Planning for the Installation
First of all, the supporting framework provided with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is very important to see to it that if the faucet includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to split a rigid seal, triggering the water to permeate the wall in between the bathroom and the tiling, bring about issues with wetness as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to permit the activity experienced when the bathtub remains in use. The sealant can split fairly early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily offered on the market. It is recommended to fit the tiles making use of water-resistant or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about How to Install a Bathtub Yourself? Try leaving feedback down below. We will be glad to hear your ideas about this piece. In hopes that you visit us again soon. Enjoyed our blog entry? Please share it. Help others locate it. We treasure reading our article about Installing A Bathtub.
Avoid further plumbing damage; call. Report this page